1.fiberglass pultrusion profiles
4.good dimension stability
Pultrusion composite fiberglass frp t shape profile
1)FRP products are with low weight and high strength .Density: 1.5-2, 1/4 of carbon steel, but the same tensile strength with carbon steel. So the FRP products can be widely used in aerospace, rockets, high-pressure container, and so on.
2)Great decay resistance
FRP product has good decay resistance, it has good ability to resist to air, water and general concentration of acid, alkali, salt, and a variety of solvent oil. So, it also can be used in chemical anticorrosion to replace steel, wood and other mentals.
3) Good electrical performance FRP is a good insulation material, it can keeps good dielectric properties under high frequency.
4)Good microwave permeability, so it is widely used to make radar antenna mask.
5)Good thermal performance.FRP is with low thermal conductivity, in room temperature, its 1.25~1.67kJ/ (m.h.k), is excellent insulation material.
6)Good plasticity;The material can be made into everything according to consumers' request
During the pultrusion process,the raw material are pulled through a heated steel forming die using a continuous pulling device. when the reinforcements are saturated with the resin mixture in the resin bath and the wetted reinforcement package is wrapped in a surfacing veil. the completed package then goes into a performer that roughly forms the package into the appropriate shape to enter the heated die for curing. the die is the exact shape of the final part desired. upon exiting the die, the part is over 90% cured and solid. the length of the part required is pulled through the cutoff saw and the process is complete.
3. Material: FRP,fiberglass
1)reinforcement material:fiberglass, glass mat, continuous strand mat, surfacing mat, needled mat.
2)basis material:unsaturated polyester resin,epoxy resin,vinylester resin
4.Application of FRP Profile:
2)cable tray,radome,insulation ladder,etc.
3)Chemical anti-corrosion markets
grating floor, handrail, working platform, undergrand pression pipe, stairs,etc.
4)building construction markets,bridge protection closed system,movable house structure,working platform,window frame, window sash and its components,etc
5)foundation engineering markets freeway antiglare shield and its handrail,lamp post,water treatment,bracket for huge industry cooling tower,etc
FAQ about FRP
Q: Can Fiber Reinforced Panels be installed over most substrates?
A: Fiber reinforced panels could be installed almost on all substrates. However, the installation method used will vary from one substrate to another.
Q: How to Install Fiberglass reinforced panels over Drywall?
A: Yes, FRP can be installed almost on all substrates by mechanical installation method. However if the contractor wants to install Fiberglass reinforced panels using adhesives, it could be done, just need to use solvent free adhesive only over porous surfaces such as concrete block, drywall, plywood or plaster walls. When installing FRP over non-porous surfaces, such as wall tiles, using a solvent base adhesive with rivets is recommended, In order to complete a better installation, remember to sand the tiles so the FRP could adhere better.
Q: Does Fiberglass reinforced panels could be installed flat against the wall?
A: FRP panels are so flexible so it can be installed flat against the wall. But remember as any building material, it will expand and contract according to environmental conditions where it was installed.
Q: What tools are required to install FRP?
A: The installation of FRP could be done by using: a fine tooth saw blade, carbide drill bit, the manufacturer's recommended trowel, and a laminate roller that will be used to ensure maximum adhesion between FRP and the surface where it is being installed.
Q: In what size does FRP is manufactured?
A: Fiberglass reinforced panels usually are manufactured in 4 foot by 8 foot sections and with some architectural trims and/or moldings. For small applications and surfaces the FRP could be cut to exact dimensions by using a power saw with a fine tooth, carbide tip blades or masonry blades. FRP Panels in 1mm thickness weigh about 1.5kg per square meter.
Q: What could be a possible solution and faster installation procedure?
A: Fiberglass reinforced panels could be supplied with pre-laminated sheets of plywood,EPS insulation or drywall. By using this type of FRP, it will allow a faster installation and will produce a smoother surface, because it eliminates the need for rivets. It is also recommended before installing FRP to remove the packing of the panels, in the area where it will be installed. FRP ideally will absorb the same environmental conditions of the place where the panels will be installed.
|Why you should choose us?|
|ZLRC is one of the biggest FRP manufacturers in China,We are specialized in FRP products .we have all kinds of FRP making machines,such as FRP pipe machine,FRP tank machine, FRP pultrusion machine,FRP grating machine,FRP sheet machine and so on.|
|ZLRC has passed the quality management system of ISO9001, ISO14001. Our technical research team are with 2 professors, 3 senior engineers and 8 doctors, possessing 16 advanced technical patents. |
|We can, therefore, guarantee to provide our customers with competitive prices, strictly quality control, prompt delivery and different products.|
We are looking forward to cooperate with you! If you are interested, kindly feel free to contact us!